Post by casesensitive on Jan 5, 2018 17:13:03 GMT
Now SOLD.
Hi all,
Santa was good to me (don't tell SWMBO), and some Jenvey 45s and DanST manifold were found under the tree, so my GSXR ITBs need a new home.
Here are the basics
GSXR1000 K1 (2001) 48mm ITBs with injector holes bunged up with JB weld (removable)
I went down the route of bending the interlink tabs rather than welding tabs to them, may need to tweak for your own fitting, balanced by eyeball only see first video below.
GSXR Throttle Position sensor and wiring connector, as well as as much of the tail as I could spare from my loom.
ST170 stub manifold, ported to match bodies, from oval to round, see album
DanST fitting kit (silicone joiners, 8 Mikalor clips, 5mm threaded bar, and some aluminium spacer bar 180mm that I didn't bother cutting up to use)
DanST trumpet mounting rings x4
Legit DanST pipercross backplate, that I found unsuitable due to inter-body spacing!
Pretty reasonable copy of this made from 1.5mm aluminium that worked much better for my application, with an M12 drillhole where my Air Temp Sensor goes (that isn't included, but was only a tenner)
And a primitive 3mm x 12mm bar mild steel contraption of my own devising, couple of small welds to hold it all in place, including little pads to hold the bungs into the injector holes, in case of misfire, picture below.
I'm including 2x low-profile (30mm maybe) tapered
trumpets in great nick, the other two, which are damaged, are free if you buy the rest, can't be charging for wrecked stuff.
Vacuum barbs and piping
All the spare Gixer bits and bobs, if ya want them, sitting in a box in my garage
I reckon £200 plus postage is fair. Another £50 if you want the 90mm aluminium trumpets. Box is 470x370x150mm and 5Kg, so postage to mainland UK main cities is approx €32.50.
Album of loads of pictures is here:
www.flickr.com/photos/43278150@N00/albums/72157691923251355
Balanced by eye
But what you really want is the sound of them, installed.
Excludes: the 90mm trumpets, filter, fuel rail (I use the standard 2.0 one anyway!), fuel pressure reg (also from 2.0), wiring, injectors, screws and the 3 clips that hold the filter onto the backplate.
Read more: mevowners.proboards.com/thread/3946/rocket-st159?page=46#ixzz53Kbflo00
Selection here.
Hi all,
Santa was good to me (don't tell SWMBO), and some Jenvey 45s and DanST manifold were found under the tree, so my GSXR ITBs need a new home.
Here are the basics
GSXR1000 K1 (2001) 48mm ITBs with injector holes bunged up with JB weld (removable)
I went down the route of bending the interlink tabs rather than welding tabs to them, may need to tweak for your own fitting, balanced by eyeball only see first video below.
GSXR Throttle Position sensor and wiring connector, as well as as much of the tail as I could spare from my loom.
ST170 stub manifold, ported to match bodies, from oval to round, see album
DanST fitting kit (silicone joiners, 8 Mikalor clips, 5mm threaded bar, and some aluminium spacer bar 180mm that I didn't bother cutting up to use)
DanST trumpet mounting rings x4
Legit DanST pipercross backplate, that I found unsuitable due to inter-body spacing!
Pretty reasonable copy of this made from 1.5mm aluminium that worked much better for my application, with an M12 drillhole where my Air Temp Sensor goes (that isn't included, but was only a tenner)
And a primitive 3mm x 12mm bar mild steel contraption of my own devising, couple of small welds to hold it all in place, including little pads to hold the bungs into the injector holes, in case of misfire, picture below.
I'm including 2x low-profile (30mm maybe) tapered
trumpets in great nick, the other two, which are damaged, are free if you buy the rest, can't be charging for wrecked stuff. Vacuum barbs and piping
All the spare Gixer bits and bobs, if ya want them, sitting in a box in my garage
I reckon £200 plus postage is fair. Another £50 if you want the 90mm aluminium trumpets. Box is 470x370x150mm and 5Kg, so postage to mainland UK main cities is approx €32.50.
Album of loads of pictures is here:
www.flickr.com/photos/43278150@N00/albums/72157691923251355
Balanced by eye
But what you really want is the sound of them, installed.
Excludes: the 90mm trumpets, filter, fuel rail (I use the standard 2.0 one anyway!), fuel pressure reg (also from 2.0), wiring, injectors, screws and the 3 clips that hold the filter onto the backplate.
Read more: mevowners.proboards.com/thread/3946/rocket-st159?page=46#ixzz53Kbflo00
Selection here.
